Save 50% on Replacement Chain for EGO Power+ CS1613 / CS1604 / CS1600 / CS1610 / CS1611 16-Inch 56V Chainsaw

16-inch replacement chain fitment for EGO Power+ CS1613, CS1604, CS1600, CS1610, and CS1611

This replacement chain is intended for select EGO Power+ 16-inch 56V chainsaws, specifically the CS1613, CS1604, CS1600, CS1610, and CS1611. If your saw is one of those models and it is equipped with the original 16-inch bar setup, this chain is designed to restore smooth cutting and dependable performance.

A fresh chain can make a big difference in how a cordless saw feels in the cut. When the fit is correct and the chain is properly tensioned, you can expect cleaner cuts, less strain on the saw, and easier day-to-day use.

Will this chain fit your saw?

The simplest starting point is your model number. According to the original listing, this chain fits these EGO Power+ chainsaws:

• EGO Power+ CS1613
• EGO Power+ CS1604
• EGO Power+ CS1600
• EGO Power+ CS1610
• EGO Power+ CS1611

Even if your saw is one of the compatible models above, it is still smart to confirm the chain specs on your current bar or in your owner’s manual before ordering. Chainsaw chains are matched by four key details:

• Bar length: this product is for a 16-inch setup
• Pitch: must match the drive sprocket and bar
• Gauge: must match the width of the bar groove
• Drive-link count: must match the bar exactly

If any one of those measurements is different, the chain may not fit or run correctly. The model match listed above is the main fitment reference provided, but checking the markings on your existing bar is the best way to avoid ordering the wrong chain if your saw has ever been changed from its factory bar-and-chain combination.

A quick tip: many bars have the chain spec stamped or printed near the mounting end. If you still have the original chain, you can also compare its markings or packaging information. For buyers replacing a worn-out chain on a stock EGO Power+ CS1613, CS1604, CS1600, CS1610, or CS1611 with a 16-inch bar, this listing is meant for that application.

Replacing the chain

Before working on any chainsaw, remove the battery and wear gloves. Chain cutters are sharp even when dull.

1. Remove the battery and let the saw cool if it was recently used.
2. Loosen the side cover and remove the bar and old chain.
3. Clean sawdust and oil buildup from the bar groove, sprocket area, and side cover.
4. Install the new chain on the bar, making sure the cutter direction matches the normal forward rotation of the chain on the top of the bar.
5. Refit the bar and side cover, then adjust chain tension so the chain sits snugly in the bar groove but can still be pulled around by hand with a gloved hand.
6. Reinstall the battery only after everything is secure, then test chain movement and oiling before cutting.

After the first few cuts, recheck tension. New chains often stretch slightly during initial use and may need a minor readjustment.

Keeping it sharp

A sharp chain is safer and easier on both the motor and battery. If the saw starts producing fine dust instead of chips, pulls to one side, or needs pressure to cut, the chain likely needs sharpening.

A few practical habits help chain life:

• Keep the chain out of dirt, rocks, and old fencing wire, which dull cutters quickly.
• Maintain proper chain tension, because a chain that is too loose or too tight wears faster.
• Make sure bar oil is flowing correctly every time you use the saw.

If the cutters are badly damaged or the chain has been sharpened down significantly, replacement is usually better than continued touch-up.

FAQ

Will this fit every EGO Power+ chainsaw with a 16-inch bar?
Not automatically. This listing specifically names the CS1613, CS1604, CS1600, CS1610, and CS1611. You should still confirm bar length, pitch, gauge, and drive-link count on your saw.

Can I install this chain if I changed to a different bar?
Only if the replacement bar uses the exact same chain specifications. A 16-inch length alone is not enough to guarantee fit.

Discount information

The original listing includes this coupon code:

• Use Coupon Code: 50W1I5CW

It also provides this shopping link:

• Shop Now！

If you are replacing the chain on an EGO Power+ CS1613, CS1604, CS1600, CS1610, or CS1611, confirming your bar specs before ordering is the best way to ensure a smooth, correct fit.