2PC 14 Inch Chainsaw Chain for Craftsman CMECS614

14-inch replacement chain fitment for Craftsman CMECS614

This 2-pack of 14-inch chainsaw chains is a fitment match for the Craftsman CMECS614 when your saw uses a 14-inch bar and the chain size is 3/8”, .050” gauge, with 52 drive links. It’s a practical replacement option if you want a fresh working chain ready to install and a spare on hand for cleanup, storm work, or routine yard cutting.

Will this chain fit your saw?

To confirm fitment on your Craftsman CMECS614, match all four chain specs, not just the bar length:

• Bar length: 14”
• Pitch: 3/8”
• Gauge: .050”
• Drive links: 52

If your current chain or guide bar markings show those exact numbers, this chain should be the correct fit. Bar length alone is not enough, because different 14-inch bars can use different chain sizes.

This chain is listed as a replacement for the following models:

• Craftsman CMECS614
• Worx WG305.1
• Worx WG305 14″ Electric Chainsaw
• Sun Joe SWJ599E
• Sun Joe SWJ699E
• GreenWorks 20222
• GreenWorks 9A 20012 Chainsaw
• Husqvarna 120 Mark II
• Husqvarna 240
• Husqvarna 135 14-in Gas Chainsaw
• RY40530
• RY40503BTL
• RY405010BTL
• RY405100 Cordless Chainsaw
• RYOBI RY3714 Gas Chainsaw
• ECHO CS-310-14 Gas Chainsaw
• Makita UC3551A
• Makita EA3201SRBB Handle Chainsaw
• Makita EA3200SRBB
• BLACK+DECKER BECS600

If you’re replacing the original chain on a Craftsman CMECS614, the most important check is still the chain spec itself: 3/8”, .050”, 52 drive links. If your saw has had the bar changed at some point, verify the bar stamp or the old chain before ordering.

Replacing the chain

Chain replacement on the Craftsman CMECS614 is straightforward, but safety comes first.

1. Unplug the saw and let it cool completely before touching the chain or bar.
2. Remove the side cover, then take off the old chain and guide bar. Clear away packed sawdust from the cover, bar groove, and sprocket area.
3. Install the chain on the bar, making sure the cutting edges on the top of the bar face forward toward the bar tip.
4. Loop the chain around the drive sprocket and seat the bar back into place. Confirm the drive links sit properly in the bar groove.
5. Reinstall the side cover and adjust chain tension so the chain sits snug against the bar but can still be pulled around by hand with a gloved hand.
6. Recheck tension after a short test run. A new chain often stretches slightly during its first uses.

A chain that is too loose can derail. Too tight can overheat the bar, chain, and motor. On an electric model like the CMECS614, correct tension helps both cutting performance and component life.

Keeping it sharp

A sharp chain cuts faster, pulls less current, and is easier on the saw.

• Avoid cutting into dirt, old fence wire, or roots. Even brief contact can dull cutters quickly.
• Keep chain oil topped up and make sure oil is reaching the bar. Good lubrication reduces heat and slows wear on the chain and bar rails.
• Touch up the chain at the first sign of fine dust, crooked cutting, or the need to force the saw through wood. Those are common signs the edge is getting dull.

If one side of the chain seems to cut more aggressively than the other, the saw may start curving in the cut. That usually means the cutters need even sharpening or the bar needs inspection for wear.

FAQ

Does this chain fit the Craftsman CMECS614 just because the bar is 14 inches?

No. You should match all specs: 14” bar, 3/8” pitch, .050” gauge, and 52 drive links. Those full measurements are what determine proper fit.

Can I use this chain on other 14-inch saws?

Only if those saws use the same chain size. This chain is specifically listed for models including Worx WG305.1, Sun Joe SWJ599E, GreenWorks 20222, Husqvarna 120 Mark II, RY40530, RYOBI RY3714, ECHO CS-310-14, Makita UC3551A, and BLACK+DECKER BECS600, along with the other compatible models listed above.